An on-line method for Cd and Pb pre-concentration and simultaneous determination in acid digested seafood by inductively coupled plasma optical emission spectrometry (ICP OES) was developed. The on-line pre-concentration was based on the complex formation of the analytes with the ammonium salt of O,O-diethyldithiophosphate (DDTP) and using the Amberlite XAD-4 resin as a solid support in a homemade column. Different conditions of the flow injection system, such as solutions flow rates, nebulizer pressure and eluent concentration were optimized. Three certified reference materials of lobster hepatopancreas, dogfish liver and fish protein, three samples of fish muscle and three samples of shrimp were digested with HNO3, H2O2 and H2SO4 in a microwave system under reflux. DDTP was added in the solutions obtained, and the mixture was injected in the FI system. Calibration curves for Cd and Pb were obtained using the standard solutions in the concentration range 0.05-0.5 µg mL-1 in the digestion medium, submitted to the same pre-concentration procedure. The quantification limits (3.3 x LOD) for 5 min of pre-concentration time were 0.005 mg kg-1 Cd2+ and 0.1 mg kg-1 Pb2+ in the sample of fish or shrimp in natura, considering 1.0 g of the sample in a final volume of 50 mL. The agreement of the obtained concentrations with the certified ones (Student t-test, 95% confidence) and the recoveries of spiked real samples, from 90 to 120%, demonstrated good accuracy. Precision was also adequate, with relative standard deviations from 2 to 13%. The method was accurate, precise and certainly could be applied to the digested samples of different natures.

A method for evaluating inorganic constituents in the grass by ICP OES is proposed. The samples were digested with nitric acid plus hydrogen peroxide in a microwave system. Seventeen samples were collected in the metropolitan area of Curitiba and Castro in the Paraná State, Brazil. The following elements were studied: Al, As, Ba, Ca, Cd, Co, Cr, Cu, Fe, K, Mg, Mn, Mo, Na, Ni, P, Pb, Sb, Se and Zn. The linear coefficients of the curves were higher than 0.999 and the precision, expressed as the relative standard deviation, which was below 10%, being considered adequate. The accuracy was validated by using the recovery test (recoveries from 80 to 107%) and by the analysis of botanical certified materials. For one sample, two other digestion procedures, using two different mixtures of nitric and hydrochloric acids, produced results in agreement with the adopted procedure. Eleven out of the twenty studied elements could be quantified in real samples. High concentrations of Ca, K, Mg and P, the essential elements for bovines and other animals, were found. The results were evaluated using the principal component analysis that gathered the samples in three groups, according to the areas where the plants were grown.

Propõe-se uma nova maneira de gerar vapor de mercúrio em altos valores de pH pela adição de NaOH ou de outra base a uma solução contendo íons de mercúrio, sem utilizar redutor, como NaBH4 ou SnCl2. Após dissolução total da amostra em sistema de microondas fechado, empregando HNO3 e H2O2, o pH da solução da amostra é elevado para 13 com NaOH. Após 90 min de repouso, o vapor frio é transportado até o plasma por um fluxo de gás argônio. O Hg é determinado em 253,652 nm em um espectrômetro de emissão óptica com plasma indutivamente acoplado com configuração axial. O procedimento foi aplicado a cinco amostras biológicas certificadas obtendo-se um limite de detecção (3s, n = 10) de 0,04 µg g-1 para uma massa da amostra de 0,5 g em um volume final de 50 mL. A calibração foi realizada com soluções padrão aquosas em NaOH 0,1 mol L-1. O procedimento foi eficiente, com recuperações dos valores certificados entre 85 e 113%, demonstrando concordância entre o valor encontrado e o certificado para um nível de 95% de confiança (teste-t). A precisão apresentou resultados aceitáveis com desvios padrão relativos de 7 a 9%. Mercúrio a partir de espécies orgânicas em solução, não foi detectado; somente Hg2+ em solução produz sinal. O procedimento é novo, simples, pode permitir estudos de especiação e serve para demonstrar liberação de vapor de mercúrio de soluções aquosas em altos valores de pH.

A novel approach to the generation of mercury vapor at high pH by the simple addition of NaOH or other base to a solution containing mercury ions is described. Subsequent addition of another reducing agent, such as NaBH4 or SnCl2, is unnecessary. Following total dissolution of sample using HNO3 and H2O2 in a closed microwave vessel, the pH of the sample solution is increased to 13 by the addition of NaOH. After standing for 90 min in a closed vessel, the Hg0 is directed to the plasma by a flow of argon. Emission from mercury is measured at 253.652 nm by an axial view inductively coupled plasma optical emission spectrometer (ICP OES). The procedure was applied to five certified biological samples, yielding a detection limit (3s, n = 10) of 0.04 µg g-1 based on a nominal sample mass of 0.5 g in a final volume of 50 mL. Calibration was achieved using simple aqueous standard solutions containing 0.1 mol L-1 NaOH. The procedure was efficient, with determined values lying in the range of 85-113 % of the certified values, showing good agreement at the 95% confidence level (t-test). The precision was fit for purpose, with relative standard deviations ranging from 7 to 9%. Organomercury species in solution were not detected; only Hg2+ in solution produces a signal. This new procedure provides for a simple approach to quantitation (and potentially speciation).

Um método para determinação de Na e K em biodiesel proveniente de diferentes óleos vegetais é proposto. São combinadas as vantagens da FAES com a simplicidade da preparação da amostra por microemulsão e calibração usando padrões aquosos. As microemulsões foram preparadas pela mistura de biodiesel, n-propanol e solução aquosa ácida, permitindo o uso de padrões inorgânicos para a calibração. Foram comparadas a introdução discreta (DA) e aspiração contínua (CA) da amostra apresentando LODs semelhantes, na ordem de 0,1 µg g-1 para ambos analitos, que são adequados para a determinação dos mesmos, conforme os limites estabelecidos na legislação brasileira. A exatidão do método foi avaliada por testes de recuperação, com resultados entre 83% e 120% e, por meio da comparação dos resultados obtidos por ICP OES.

A method for the determination of Na and K in biodiesel, from different vegetable oils, is proposed. The advantages of the FAES were combined with the simplicity of microemulsion preparation and calibration using aqueous standards. Microemulsions were prepared by mixing biodiesel samples with n-propanol and aqueous acid solution, which allowed the use of inorganic aqueous standards for the calibration. Sample introduction through discrete aspiration (DA) or by continuous aspiration (CA) were compared, presenting similar LODs, in the order of 0.1 µg g-1 for both analytes, adequate to the established limits in the Brazilian legislation. The accuracy of the method was checked through recovery tests, with results between 83% and 120%, and through the comparison of the results with those obtained by ICP OES.

O presente trabalho apresenta um estudo comparativo das técnicas ICP-MS e ICP OES com configuração axial e também de dois métodos diferentes de tratamento das amostras, ou seja, por dissolução total com e sem separação do cobre por eletrodeposição, para as determinações de As, Fe, Mn, Pb, Sb e Sn em amostras de cobre eletrolítico. Amostras comerciais e industriais foram dissolvidas com HNO3 5% v/v e o cobre foi eletrodepositado em meio de HNO3 (1,4% v/v) e H2SO4 (2,0% v/v). Verificou-se que a separação do cobre foi eficiente, contudo se constatou contaminação de Fe e Sn durante o processo de eletrodeposição. As determinações foram realizadas utilizando-se um ICP OES Axial Varian (Vista Pro) e um ICP-MS Perkin Elmer (Elan Sciex 6000). Foi aplicada a calibração externa, com soluções padrão contendo ou não cobre na concentração equivalente à da amostra. Os limites de detecção (3s, n=10) para a técnica de ICP OES foram bastante semelhantes na presença ou não do cobre). Já usando ICP-MS, os limites foram melhores na ausência do cobre. Com o objetivo de estabelecer o nível de significância entre as técnicas de quantificação, ou seja, entre ICP OES e ICP-MS,foi aplicado o teste t emparelhado, que demonstrou, para um nível de confiança de 95%, não haver diferença significativa, tanto para as soluções sem ou com cobre. Os resultados obtidos no presente trabalho demonstraram que as técnicas ICP-MS e ICP OES fornecem resultados similares em determinadas faixas de concentração dos analitos, podendo ambas serem utilizadas, no controle de qualidade do cobre eletrolítico. Contudo, a técnica ICP-MS foi superior em termos de limite de detecção.

The performance of axial view ICP OES and ICP-MS techniques were compared through the determination of As, Fe, Mn, Pb, Sb and Sn in electrolytic copper. Samples were prepared by two procedures: 1. Total dissolution with 5 % v/v HNO3 and 2. Dissolution with 1.4 % v/v HNO3 plus 2.0 % v/v H2SO4, followed by separation of the Cu by electrodeposition. The methods were applied for the analysis of standard copper solutions, using calibration against aqueous solutions with or without the addition of Cu. The results obtained by the two techniques were similar, but the separation of Cu from the sample matrix proved to be more adequate for practical reasons.

Um sistema de injeção em fluxo envolvendo complexação com dietilditiofosfato de amônio e sorção de complexos metálicos em minicolunas de sílica gel modificada por grupos octadecil C18 é proposto para determinações multielementares em espectrometria de massa com plasma indutivamente acoplado. Influência da concentração de reagentes, natureza do ácido, tempo de reação, tempos de comutação, vazões e interferência de sódio foram investigadas. Água ou solução 2% v/v HNO3 podem ser utilizadas para lavar a coluna antes da eluição dos analitos com etanol. Amostras contendo 5000 mg Na L-1 e analisadas diretamente com o sistema proposto produzem uma concentração aparente de 63Cu de 0,45 µg L-1; por outro lado não foi observada interferência para As, Pb, Bi, Se, In, Tl, Cd, Hg e 65Cu. Para 0,25 % w/v NH4DTP e 3 mL de solução de amostra, curvas analíticas para Bi, Cu, Pb, As, Se, In, Tl, Cd, Hg no intervalo de 0,10 a 2,00 µg L-1 podem ser construídas com boas correlações (r2 > 0.998). A velocidade analítica e sensibilidade podem ser melhoradas pois dependem das condições de pré-concentração e eluição selecionadas. Com os parâmetros acima fixados, limites de detecção de 0.014 (Cu), 0.027 (As), 0.06 (Se), 0.02 (Cd), 0.029 (In), 0.043 (Hg), 0.02 (Tl), 0.06 (Pb) e 0.002 µg L-1 (Bi) foram obtidos.

Complexation with ammonium diethyl dithiophosphate and sorption on a C18 bonded silica gel minicolumn in flow system was exploited for on-line separation and preconcentration in inductively coupled plasma mass spectrometry. Influence of interaction time between metallic ions and ligand, ligand concentration, nature and concentration of acid, timing, flow rates and minimization of spectral interference due to sodium were studied. Metallic complexes were stripped from the solution and retained in the minicolumn. Other ions that do not form complexes pass through the column promoting the separation of the matrix. Selectivity was improved with sequential elution. Water or 2% v/v HNO3 solution can be used for minicolumn washing before analyte elution with ethanol. When samples with sodium content up to 5000 mg L-1 were directly analysed in system, 63Cu apparent concentration of only 0.45 µg L-1 was detected while no interference were observed for As, Pb, Bi, Se, In, Tl, Cd, Hg and 65Cu. For 0.25 % of ligand solution and 3 mL sample volume in 2 % (v/v) HNO3, analytical curves for Bi, Cu, Pb, As, Se, In, Tl, Cd, Hg in the 0.10-2.00 µg L-1 range were obtained (r > 0.998). Sampling rate and detection limit depend on the selected conditions for concentration and elution. Detection limits for Cu, As, Se, Cd, In, Hg, Tl, Pb, and Bi were 0.014, 0.27, 0.06, 0.02, 0.29, 0.43, 0.02, 0.06 and 0.002 µg L-1, respectively.

An automatic dispenser based on a flow-injection system used to introduce sample and analytical solution into an inductively coupled plasma mass spectrometer through a spray chamber is proposed. Analytical curves were constructed after the injection of 20 to 750 µL aliquots of a multielement standard solution (20.0 µg L-1 in Li, Be, Al, V, Cr, Mn, Ni, Co, Cu, Zn, As, Se, Sr, Ag, Cd, Ba, Tl, Pb) and the acquisition of the integrated transient signals. The linear concentration range could be extended to ca. five decades. The performance of the system was checked by analyzing a NIST 1643d reference material. Accuracy could be improved by the proper selection of the injected volume. Besides good precision (r.s.d. < 2%), the results obtained with the proposed procedure were closer to the certified values of the reference material than those obtained by direct aspiration or by injecting 125 µL of several analytical solutions and samples.

A method for the determination of phosphorus in steel samples by graphite furnace atomic absorption spectrometry, using the Zeeman effect background correction and the STPF conditions is proposed. The effect of iron (III) on the phosphorus signal was studied. It was verified, through the pyrolysis temperature curves, that iron (III) is an efficient chemical modifier, thermically stabilizing phosphorus up to 1400ºC. The phosphorus signal increases with the iron (III) concentration, but in the range, which corresponds to the usual concentrations of iron in the sample solutions, the increase is small. Phosphorus was determined in three standard reference materials, after its dissolution in a mixture of hydrochloric and perchloric acids in a PTFE bomb. The agreement with the certified concentration values was excellent. Iron (III) was added to the reference analytical solutions prepared in the blank of the dissolution, while the sample solutions were measured directly, since they already contained the modifier. The detection limit (k = 2) was 0.0042% of phosphorus in the steel sample.